CVE-2026-64513: In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Unconditionally recompute CR8 intercept on PPR update The TPR_THRESHOL...

Description

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Unconditionally recompute CR8 intercept on PPR update The TPR_THRESHOLD field in the VMCS is used by VMX to induce VM exits when the guest's virtual TPR falls under the specified threshold, allowing KVM to inject previously masked interrupts. KVM handles these VM exits in handle_tpr_below_threshold(). Commit eb90f3417a0c ("KVM: vmx: speed up TPR below threshold vmexits") optimized this function by calling apic_update_ppr() instead of raising KVM_REQ_EVENT. apic_update_ppr() then raises KVM_REQ_EVENT if there is a pending, deliverable interrupt. However, if there are no new interrupts pending, apic_update_ppr() does not issue the request. Thus, kvm_lapic_update_cr8_intercept() and vmx_update_cr8_intercept() are not called before VM entry, which results in a high, stale TPR_THRESHOLD. This is problematic due to the following sentence in 28.2.1.1 "VM-Execution Control Fields" in the SDM: The following check is performed if the “use TPR shadow” VM-execution control is 1 and the “virtualize APIC accesses” and “virtual-interrupt delivery” VM-execution controls are both 0: the value of bits 3:0 of the TPR threshold VM-execution control field should not be greater than the value of bits 7:4 of VTPR. This error condition is typically not observed when KVM runs on a bare metal system because modern processors support APICv, which enables virtual-interrupt delivery, and which KVM uses when possible. This causes the processor to no longer generate TPR-below-threshold exits and to no longer check TPR_THRESHOLD on entry. However, when running on older platforms, or under nested virtualization on a hypervisor that does not support virtual-interrupt delivery and enforces this check (like Hyper-V) this can cause a VM entry failure with hardware error 0x7, as seen in [1]. Call kvm_lapic_update_cr8_intercept() if apic_update_ppr() does not find a deliverable interrupt (and thus does not raise KVM_REQ_EVENT). Remove calls to kvm_lapic_update_cr8_intercept() on paths that end up in apic_update_ppr(), as they now become redundant. This ensures that any path that updates the guest's PPR also figures out if KVM needs to wait for a TPR change (using TPR_THRESHOLD on VMX or CR8 intercepts on SVM).

Affected Software

Source: CNA advisory (CVE.org). NVD analysis pending.

Vendor	Product	Versions
Linux	Linux	>= eb90f3417a0cc4880e979ccc84e41890d410ea5b, < ff9c4c6428883182960cfe5c78928f0896d80ebc; >= eb90f3417a0cc4880e979ccc84e41890d410ea5b, < 8c8e8ac22ee17d52f9eb2bc814bca7fab90fb8df; >= eb90f3417a0cc4880e979ccc84e41890d410ea5b, < bb365a506b1e6fb050c0fceaad354fe395385ef0
Linux	Linux	4.11

References

Timeline

Published: Jul 25, 2026
Last Modified: Jul 25, 2026
Status: Received

Frequently Asked Questions

What is CVE-2026-64513?

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Unconditionally recompute CR8 intercept on PPR update The TPR_THRESHOLD field in the VMCS is used by VMX to induce VM exits when the guest's virtual TPR falls under the specified threshold, allowing KVM to inject previously masked interrupts. KVM handles these VM exits in handle_tpr_below_threshold(). Commit eb90f3417a0c ("KVM: vmx: speed up TPR below threshold vmexits") optimized this function by calling apic_update_ppr() instead of raising KVM_REQ_EVENT. apic_update_ppr() then raises KVM_REQ_EVENT if there is a pending, deliverable interrupt. However, if there are no new interrupts pending, apic_update_ppr() does not issue the request. Thus, kvm_lapic_update_cr8_intercept() and vmx_update_cr8_intercept() are not called before VM entry, which results in a high, stale TPR_THRESHOLD. This is problematic due to the following sentence in 28.2.1.1 "VM-Execution Control Fields" in the SDM: The following check is performed if the “use TPR shadow” VM-execution control is 1 and the “virtualize APIC accesses” and “virtual-interrupt delivery” VM-execution controls are both 0: the value of bits 3:0 of the TPR threshold VM-execution control field should not be greater than the value of bits 7:4 of VTPR. This error condition is typically not observed when KVM runs on a bare metal system because modern processors support APICv, which enables virtual-interrupt delivery, and which KVM uses when possible. This causes the processor to no longer generate TPR-below-threshold exits and to no longer check TPR_THRESHOLD on entry. However, when running on older platforms, or under nested virtualization on a hypervisor that does not support virtual-interrupt delivery and enforces this check (like Hyper-V) this can cause a VM entry failure with hardware error 0x7, as seen in [1]. Call kvm_lapic_update_cr8_intercept() if apic_update_ppr() does not find a deliverable interrupt (and thus does not raise KVM_REQ_EVENT). Remove calls to kvm_lapic_update_cr8_intercept() on paths that end up in apic_update_ppr(), as they now become redundant. This ensures that any path that updates the guest's PPR also figures out if KVM needs to wait for a TPR change (using TPR_THRESHOLD on VMX or CR8 intercepts on SVM).

How severe is CVE-2026-64513?

Severity scoring for CVE-2026-64513 is pending analysis.

How do I fix CVE-2026-64513?

Check the vendor references and advisories linked above for patched versions and mitigation guidance. You can also run a Strix scan to test if your systems are affected.

How Strix Helps

Related CVEs from 2026

View all 2026CVEs →