CVE-2026-79976: zephyr NULL Pointer Dereference (CVSS 7.1)

Description

The MCTP-over-I2C+GPIO target binding in subsys/pmci/mctp/mctp_i2c_gpio_target.c emulates a small pseudo-register file, where the bus controller first writes a register number and then writes or reads payload bytes. The selected register (b->reg_addr) and the data-phase flag (b->rxtx) were never cleared when the controller issued an I2C STOP, so after a completed transfer the target still had a data register selected while the packet buffer that register refers to had already been consumed and set to NULL by mctp_i2c_gpio_target_stop(). A controller on the bus can re-enter the same branch of mctp_i2c_gpio_target_stop() with a NULL buffer using two ordinary transactions and no authentication: first a normal packet write to MCTP_I2C_GPIO_RX_MSG_ADDR followed by STOP (which delivers and frees b->rx_pkt), then a bare read transaction followed by STOP. The failing read_requested() call leaves the stale state untouched and the I2C driver still delivers the STOP callback, which then calls mctp_bus_rx() with a NULL packet. The symmetric case exists on the transmit side, where the stale MCTP_I2C_GPIO_TX_MSG_ADDR selection dereferences b->tx_pkt->end after b->tx_pkt has been cleared and additionally signals b->tx_complete a second time, causing the next outbound packet to be dropped. The dereference happens in the I2C target interrupt handler, so on any target that traps accesses to address 0 the result is a fatal exception and a device reset or halt — a denial of service inflicted by any device able to act as controller on the shared management bus (for example compromised firmware on a peer MCTP endpoint or on the BMC). On parts where address 0 is readable, the impact degrades to a malformed packet buffer being handed to the MCTP stack and lost transmit packets. No attacker-controlled value is written and no confidentiality or integrity boundary is crossed. The fix resets b->reg_addr to MCTP_I2C_GPIO_INVALID_ADDR and clears b->rxtx at every STOP, so a new register must be selected before any data phase can run again. Only builds that opt into the experimental CONFIG_MCTP subsystem with CONFIG_MCTP_I2C_GPIO_TARGET=y are affected.

Metrics

CVSS 3.1

7.1/10

CVSS:3.1/AV:A/AC:L/PR:N/UI:N/S:U/C:L/I:N/A:H

EPSS Probability

0.21%

10.2th percentile

Probability of exploitation in the next 30 days. Learn more

Weakness Enumeration

CWE-476

Affected Software

Source: CNA advisory (CVE.org). NVD analysis pending.

Vendor	Product	Versions
zephyrproject	zephyr	>= 4.3.0, <= 4.4.2

References

Timeline

Published: Oct 21, 2026
Last Modified: Oct 23, 2026
Status: Awaiting Analysis

Frequently Asked Questions

What is CVE-2026-79976?

The MCTP-over-I2C+GPIO target binding in subsys/pmci/mctp/mctp_i2c_gpio_target.c emulates a small pseudo-register file, where the bus controller first writes a register number and then writes or reads payload bytes. The selected register (b->reg_addr) and the data-phase flag (b->rxtx) were never cleared when the controller issued an I2C STOP, so after a completed transfer the target still had a data register selected while the packet buffer that register refers to had already been consumed and set to NULL by mctp_i2c_gpio_target_stop(). A controller on the bus can re-enter the same branch of mctp_i2c_gpio_target_stop() with a NULL buffer using two ordinary transactions and no authentication: first a normal packet write to MCTP_I2C_GPIO_RX_MSG_ADDR followed by STOP (which delivers and frees b->rx_pkt), then a bare read transaction followed by STOP. The failing read_requested() call leaves the stale state untouched and the I2C driver still delivers the STOP callback, which then calls mctp_bus_rx() with a NULL packet. The symmetric case exists on the transmit side, where the stale MCTP_I2C_GPIO_TX_MSG_ADDR selection dereferences b->tx_pkt->end after b->tx_pkt has been cleared and additionally signals b->tx_complete a second time, causing the next outbound packet to be dropped. The dereference happens in the I2C target interrupt handler, so on any target that traps accesses to address 0 the result is a fatal exception and a device reset or halt — a denial of service inflicted by any device able to act as controller on the shared management bus (for example compromised firmware on a peer MCTP endpoint or on the BMC). On parts where address 0 is readable, the impact degrades to a malformed packet buffer being handed to the MCTP stack and lost transmit packets. No attacker-controlled value is written and no confidentiality or integrity boundary is crossed. The fix resets b->reg_addr to MCTP_I2C_GPIO_INVALID_ADDR and clears b->rxtx at every STOP, so a new register must be selected before any data phase can run again. Only builds that opt into the experimental CONFIG_MCTP subsystem with CONFIG_MCTP_I2C_GPIO_TARGET=y are affected.

How severe is CVE-2026-79976?

CVE-2026-79976 has a CVSS score of 7.1/10 (HIGH severity). The EPSS model estimates a 0.21% probability of exploitation in the next 30 days.

How do I fix CVE-2026-79976?

Check the vendor references and advisories linked above for patched versions and mitigation guidance. You can also run a Strix scan to test if your systems are affected.

How Strix Helps

Related CVEs from 2026

View all 2026CVEs →