CVE-2026-93669

MEDIUMCVSS 4.7/10

Last modified

CVE-2026-93669 is a medium-severity vulnerability rated 4.7/10 on the CVSS scale. The ITE IT8xxx2 SHI host-command backend in subsys/mgmt/ec_host_cmd/backends/ec_host_cmd_backend_shi_ite.c arms the SPI peripheral before its receive context exists. shi_ite_init_registers() sets the state machine to SHI_STATE_READY_TO_RECV and calls irq_enable() while the device initializes at POST_KERNEL priority CONFIG_KERNEL_INIT_PRIORITY_DEFAULT (40), but data->rx_ctx and data->tx are only assigned later by shi_ite_backend_init(), which ec_host_cmd_init() invokes at CONFIG_EC_HOST_CMD_INIT_PRIORITY (default 80). If the attached host processor starts a SPI transaction inside that window, the Rx-valid-length interrupt fires, shi_ite_int_handler() passes its state check and calls shi_ite_parse_header(), which stores the host-derived request length through the still-NULL data->rx_ctx.

Description

The ITE IT8xxx2 SHI host-command backend in subsys/mgmt/ec_host_cmd/backends/ec_host_cmd_backend_shi_ite.c arms the SPI peripheral before its receive context exists. shi_ite_init_registers() sets the state machine to SHI_STATE_READY_TO_RECV and calls irq_enable() while the device initializes at POST_KERNEL priority CONFIG_KERNEL_INIT_PRIORITY_DEFAULT (40), but data->rx_ctx and data->tx are only assigned later by shi_ite_backend_init(), which ec_host_cmd_init() invokes at CONFIG_EC_HOST_CMD_INIT_PRIORITY (default 80). If the attached host processor starts a SPI transaction inside that window, the Rx-valid-length interrupt fires, shi_ite_int_handler() passes its state check and calls shi_ite_parse_header(), which stores the host-derived request length through the still-NULL data->rx_ctx. On the IT8xxx2 low addresses are not backed by RAM, and with CONFIG_NULL_POINTER_EXCEPTION_DETECTION_PMP the first bytes of the address space are explicitly made inaccessible, so the store raises a fatal access fault in interrupt context. The window widens further when CONFIG_EC_HOST_CMD_INITIALIZE_AT_BOOT is disabled and the application calls ec_host_cmd_init() itself. The result is a kernel panic on the embedded controller: with Zephyr's default fatal handler the CPU halts, so the controller stops servicing host commands until a hardware reset. Because the trigger is traffic from the attached host processor -- an untrusted peer from the controller firmware's point of view -- software on that host can provoke the fault by forcing a controller reset and issuing transactions during the reboot, turning a recoverable reset into a persistent outage. Impact is limited to availability: the faulting address is fixed and not attacker-chosen, so no memory-corruption primitive follows. The fix leaves the interface at SHI_STATE_DISABLED with the interrupt masked during device init, moves irq_enable() into shi_ite_backend_init() after the buffers are published, and makes shi_ite_int_handler() reject a NULL data->rx_ctx while write-clearing IT83XX_SPI_ISR and IT83XX_SPI_RX_VLISR so that an unexpected early interrupt cannot storm.

Metrics

Weakness Enumeration

Affected Software

Source: CNA advisory (CVE.org). NVD analysis pending.

VendorProductVersions
zephyrprojectzephyr>= 3.4.0, < 4.3.2; >= 4.4.0, < 4.5.0

References

Timeline

Published
Last Modified
Status
Awaiting Analysis

Frequently Asked Questions

What is CVE-2026-93669?
The ITE IT8xxx2 SHI host-command backend in subsys/mgmt/ec_host_cmd/backends/ec_host_cmd_backend_shi_ite.c arms the SPI peripheral before its receive context exists. shi_ite_init_registers() sets the state machine to SHI_STATE_READY_TO_RECV and calls irq_enable() while the device initializes at POST_KERNEL priority CONFIG_KERNEL_INIT_PRIORITY_DEFAULT (40), but data->rx_ctx and data->tx are only assigned later by shi_ite_backend_init(), which ec_host_cmd_init() invokes at CONFIG_EC_HOST_CMD_INIT_PRIORITY (default 80). If the attached host processor starts a SPI transaction inside that window, the Rx-valid-length interrupt fires, shi_ite_int_handler() passes its state check and calls shi_ite_parse_header(), which stores the host-derived request length through the still-NULL data->rx_ctx. On the IT8xxx2 low addresses are not backed by RAM, and with CONFIG_NULL_POINTER_EXCEPTION_DETECTION_PMP the first bytes of the address space are explicitly made inaccessible, so the store raises a fatal access fault in interrupt context. The window widens further when CONFIG_EC_HOST_CMD_INITIALIZE_AT_BOOT is disabled and the application calls ec_host_cmd_init() itself. The result is a kernel panic on the embedded controller: with Zephyr's default fatal handler the CPU halts, so the controller stops servicing host commands until a hardware reset. Because the trigger is traffic from the attached host processor -- an untrusted peer from the controller firmware's point of view -- software on that host can provoke the fault by forcing a controller reset and issuing transactions during the reboot, turning a recoverable reset into a persistent outage. Impact is limited to availability: the faulting address is fixed and not attacker-chosen, so no memory-corruption primitive follows. The fix leaves the interface at SHI_STATE_DISABLED with the interrupt masked during device init, moves irq_enable() into shi_ite_backend_init() after the buffers are published, and makes shi_ite_int_handler() reject a NULL data->rx_ctx while write-clearing IT83XX_SPI_ISR and IT83XX_SPI_RX_VLISR so that an unexpected early interrupt cannot storm.
How severe is CVE-2026-93669?
CVE-2026-93669 has a CVSS score of 4.7/10 (MEDIUM severity).
How do I fix CVE-2026-93669?
Check the vendor references and advisories linked above for patched versions and mitigation guidance. You can also run a Strix scan to test if your systems are affected.

How Strix Helps

Related CVEs from 2026

Are you affected by CVE-2026-93669?

Run a free Strix scan to check your systems for this vulnerability.

Scan your code now

Source: NVD / NIST